| ********** | Service Tools | ******** |
| ST350-APT | 480-42 armature pin tightening tool | 15.00 |
| ST350-BST | 3451-5 brakestand support tool | 14.00 |
| ST350-F | press tool flat 3/4" OD | 10.00 |
| ST350-GST | GP sideframe tightning support tool | 17.50 |
| ST350-GT | 622 gauge tool pg 56 Greenberg Op | 9.50 |
| ST350-RRT | 566-16 rivet removal tool set | 25.00 |
| ST350-SET | 15 piece tool set with block | 195.0 |
| ST350-FST | frame spreader for collector plates | 20.00 |
| ST350-ELT | E-unit lever installation tool | 28.00 |
| ST350-HTA | 2332-7 horn anvil tool | 17.50 |
| ST350-3 | 3" threaded anvil holder | 9.50 |
| ST350-3X | 6" threaded anvil holder | 11.00 |
| ST350-4 | knurled thumb nut | 6.50 |
| ST350-5 | thumb screw | 1.00 |
| ST350-6 | reproduction tool block | 2.50 |
| ST350-7 | rivet anvil large (566-16 rivet) | 14.00 |
| ST350-8 | roll clincher .062 (TC-23 rivet) | 16.00 |
| ST350-9 | roll clincher .088 (shoe rivet) | 16.00 |
| ST350-9L | long roll clincher #41,51,53 rails | 19.50 |
| ST350-9S | rollover for recessed areas | 20.00 |
| ST350-9P | motorized unit handrail punch | 17.50 |
| ST350-10 | roll clincher .098 (530-40 rivet) | 16.00 |
| ST350-11 | roll clincher .125 (566-16 rivet) | 16.00 |
| ST350-12 | roll clincher .140 | 16.00 |
| ST350-13 | star clincher hardened tool steel | 16.00 |
| ST350-14 | binding post anvil (.116) | 14.00 |
| ST350-15 | binding post anvil (.144) | 14.00 |
| ST350-16 | binding post anvil (.166) | 14.00 |
| ST350-17 | sliding shoe anvil | 16.00 |
| ST350-19 | splaying clincher hard tool steel | 16.00 |
| ST350-20 | knockout punch HARD TOOL STEEL | 16.00 |
| ST350-21 | rivet anvil small | 14.00 |
| ST350-21S | rivet anvil small (knuckle rivet) | 14.00 |
| ST350-22 | knockout anvil (.250 hole) | 14.00 |
| ST671-MS | motor gear shim (2 needed) | 5.00 |
| ST375-B1 | berk wheel cup set early nickl tire | 40.00 |
| ST375-T1 | turbine wheel cups for nickle tires | 42.00 |
| ST375-T2 | turbine wheel cups sintered wheels | 42.00 |
| ST375-1 | axle mount tool for all locos | 15.00 |
| ST375-2 | upper wheel cup for all diesel loco | 18.00 |
| ST375-3 | lower wheel cup for all diesel loco | 18.00 |
| ST375-4 | upper wheel cup for 726/736 locos | 24.00 |
| ST375-5 | lower wheel cup for 726/736 locos | 24.00 |
| ST375-6 | upper wheel cup 2025,2035,665 etc | 24.00 |
| ST375-7 | lower wheel cup 2025,2035,665 etc | 24.00 |
| ST375-8 | sleeve original new LIMITED | 6.00 |
| ST375-9 | lower wheel cup reproduction | 17.50 |
| ST375-10 | upper wheel cup orig new LIMITED | 10.00 |
| AF-1008 | Amer Flyer link tool set 6 pc | 40.00 |
| HH-INSTRUC | instruction manual for HH Press | 15.00 |
| HH-SPGRIP | sponge grip for press handle | 4.50 |
| HH-1000 | Hobby Horse press & attachments | 250.0 |
| HH-1024 | Lionel knuckle rivet punch | 14.00 |
| HH-1024B | knuckle coupler anvil | 12.00 |
| HH-1026 | alco/F3 horn 3 piece tool set | 27.50 |
| HH-1027 | motorized unit handrail punch | 10.00 |
| HH-1052 | E-unit vise-reproduction | 50.00 |
| HH-1058 | prewar hook coupler install tool | 40.00 |
| HH-1062 | wheel cup mounting post | 25.00 |
| HH-1063 | track tightening tool 2 pc set | 22.00 |
| HH-1064 | knuckle coupler anvil A/B | 25.00 |
| ST-STAN | wheel puller stan gauge, diesel etc | 37.50 |
| ST-302 | spring adjusting tool reproduction | 15.00 |
| ST-303 | E unit spreader stainless steel rep | 3.50 |
| ST-311J | wheel puller thin jaw replacement | 5.00 |
| ST-311P | forcing pin small LIMITED | 2.00 |
| ST-311PL | forcing pin large LIMITED | 2.00 |
| ST-311S | wheel puller for pilot/trail wheels | 27.00 |
| ST-311PP | armature pinion gear puller | 40.00 |